In situ ultrasonic measurements: a powerful tool to control the synthesis of zeolites from coal fly ash

An in situ ultrasonic diagnostic technique was applied to monitoring the hydrothermal synthesis of zeolite A and X of clear solution extracted from alkaline fused class F coal fly ash. In this context, kinetic evaluations based on in situ ultrasonic diagnostic data displayed an important approach to study the synthesis process. The impact on nucleation and crystal growth was demonstrated by variation of a few relevant parameters such as reaction temperature, amount of water, Na₂O and ageing time, including templated colloidal synthesis mixtures as model solution. To complement the kinetic analysis, ex situ techniques such as ICP, X-ray diffraction, scanning electron microscopy and dynamic light scattering were used to investigate liquid phase and reaction products extracted from the reaction mixture during the synthesis.     

Validation of primary formaldehyde gas standards prepared by dynamic thermogravimetry through a tri-national comparison of gaseous formaldehyde amount fraction

A validation study for primary formaldehyde gas standards was performed at three National Metrology Institutes: the Korea Research Institute of Standards and Science (KRISS), the National Metrology Institute of Japan (NMIJ) and the National Institute of Metrology of China (NIM). The studied materials had a nominal amount fraction of 2 μmol/mol formaldehyde in nitrogen balance and were prepared in 10-L aluminum cylinders by KRISS. The impurities in the materials were analyzed using a gas chromatograph/atomic emission detector and a Fourier-transform infrared spectrometer (FTIR). The stability of the materials was assessed for 1 year by KRISS using paraformaldehyde as a source for the primary standard gas and a cavity ring-down spectrometer (CRDS) instrument as the measurement method. The amount fraction of formaldehyde in the materials decreased linearly by 0.74 % each month. The studied materials that exhibited similar linear rates of decline were distributed to the participants. After the measurement was completed by the participants, the materials were returned to KRISS and the stability analysis based on the primary standard maintained at KRISS was repeated. NMIJ analyzed the materials using paraformaldehyde as the source of the primary standard of formaldehyde and FTIR analysis, whereas NIM used trioxane as the primary standard gas source and CRDS analysis. The results of the comparison revealed good agreement between the results and were within the expanded uncertainty of 2 % although each of them used different combinations of methods in the generation of primary gas standards and measurements.     

Synthesis of thermally stable aromatic poly(spiroorthocarbonate)s having a Cardo or bent structure

Novel poly(spiroorthocarbonate)s [poly(SOC)]s having a Cardo or bent structure were synthesized by polycondensation of several bis‐catechols having fluorene (BCFL), spirobisindane (BCSPI), or spirobischromane (BCSPC) in the structure with 2,2,6,6‐tetrachlorobenzo[1,2‐d:4,5‐d’]bis[1,3]dioxole (4ClBD). Synthesis of poly(SOC)s was confirmed by NMR and IR spectrometry. The poly(SOC)s obtained from BCFL or BCSPC were soluble in common organic solvents. The glass transition temperature of the poly(SOC)s was not detected by differential scanning calorimetry (DSC) in the range of 50–300 °C. The 10 wt % decomposition temperature of the poly(SOC)s was found to be above 400 °C. These results indicated the high thermal stability of the poly(SOC)s. Soluble poly(SOC)s could be possessed to form a film on a glass plate by the spin coat method. The obtained polymer films were 0.2 μm in thickness with 95% light transmission in the optical wavelength range. These results suggested that the Cardo or bent structure may block the packing of the main‐chain of the structure, which improves the solubility of the polymers, increases transparency, and enhances the thermal stability of SOCs. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1409‐1416     

Glutaraldehyde crosslinking of arabinoxylan produced from corn ethanol residuals

This study investigated the possibility of substituting petroleum-based polymers with biopolymers for films and paper coatings. Arabinoxylan (AX) was extracted from distillers’ grains, a low-value corn ethanol byproduct, and modified through crosslinking with glutaraldehyde (GA) which was made into films and paper coatings. The effects of degree of substitution (DS) on film and coating properties of GA cross-linked AX, referred to as GAX, were investigated. The GAX films had markedly higher tensile strength, approximately 3 times higher than the unmodified AX films at low DS, with higher DS causing a negative effect on the film tensile strength. Compared to unmodified AX coating, paper coated with GAX also had significantly higher tensile index, presumably due to high adhesion between the coating and paper interface. When used as a coating binder with calcium carbonate pigments, GAX showed comparable performance to polyvinyl alcohol, a common industrial binder, demonstrating the potential to be substituted for the petroleum-based paper coating binder.     

Two‐Step direct arylation for synthesis of naphthalenediimide‐based conjugated polymer

A naphthalenediimide (NDI)‐based conjugated polymer was synthesized by a two‐step direct C‐H arylation sequence. In the first step, two ethylenedioxythiophene units were coupled to NDI by direct arylation. In the second step, the direct arylation polycondensation of the monomer, formed in the first step, with 2,7‐dibromo‐9,9‐dioctylfluorene afforded the corresponding NDI‐based conjugated polymer ( PEDOTNDIF ) with molecular weight of 21,500 in 91% yield. The optical and electrochemical properties of the polymer were evaluated. The polymer showed ambipolar behavior in organic field‐effect transistors (OFETs). The electron mobility of PEDOTNDIF was estimated to be 2.3 × 10^?6 cm² V^?1 s^?1 using an OFET device with source‐drain (S‐D) Au electrodes. A modified OFET device with S‐D MgAg electrodes increased the electron mobility for PEDOTNDIF to 1.0 × 10^?5 cm² V^?1 s^?1 due to the more suitable work function of these electrodes, which reduced the injection barrier to the semiconducting polymer. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1401–1407